How to Replace Your Septic Distribution Box

The septic distribution box is usually used to equally distribute wastewater from your septic tank to the dispersal field. As a matter of fact, the septic distribution box can be eroded and needs to be replaced over time. This task is not that difficult however, removing and changing the septic distribution box is actually a grueling and messy task.

The following are some of the steps on how to replace your septic distribution box:

1. Find the Septic Distribution Box

This must be very easy to perform however, it’s not always the case. The septic distribution box is basically put downhill or at the bottom of the sloping area on your property. This is the reason why they use gravity to gather and distribute water. If you were around when the septic distribution box was built, you will then know where it is. But if not, contact the local building permit office to get a record of your plans that will show the location of your distribution box.

2. Excavation

The septic distribution box is buried and made out of concrete. Remove the lid of your septic distribution box through shoveling away the dirt and debris surrounding it. Excavate until you reach the base of your distribution box and broaden your efforts so that there’s a space around your distribution box. In addition to that, you will also like to thoroughly dig out the lines, exposing a lot of feet of them.

3. Remove Your Distribution Box

The distribution box has a lot of pipe lines going into it that take in water as well as remove it to the field. Wiggle the box, moving it towards the leach field until all inlet pipes come off. Move the distribution box back to remove the pipe lines on the other portion which lead toward the field. Once the box is already free, you can now remove it.

4. Prepare the Ground

With your old distribution box removed, you should provide a flat portion for your new box. Use the level and the shovel to remove and pack down waste. Constantly inspect until the floor space is flat and level.

5. Install Your New Septic Distribution Box

Set your new septic distribution box in position by sliding on to the pipe lines leading toward the field. Aside from that, the pipes must be inside the distribution box. Line your septic system pipes up with the new septic distribution box, then slide it back until they are all placed inside the distribution box as well. Furthermore, adjust the new box so that both pipes are evenly aligned inside the distribution box.

Once you’re satisfied with it, put the plumber’s putty around the pipe lines where they enter the distribution box. Do this carefully outside as well as on the inside of the box. This basically seals all the pipes so that no leaks will ever occur. Once the plumber’s putty is in place, change the cover and rebury the septic distribution box. It’s also best that you ask the help of plumbers near me to assist you better.

Read More

Tips on Wood Flooring for Starter 

Wood flooring is slightly popular these days. Many people are looking forward to having wood flooring on walls and many more in their home. However, it can be hard if you are going to do it by yourself. So, there are many people, looking for an expert to do the job.  

 

Before you are going to find an installer of the floor, you can read the following suggestion. In this way, you will know how to prepare for wood flooring in case you want.  

1. The layout of the floor should be for strength purpose. Many people install their wood floor on lengthwise direction, for aesthetic reasons. But when you are planning on the layout of your floor, make sure it has a vertical layout to the joist. It will make the floor strong and prevents on separating and warping for a long run.
2. It would be best if you started at the level surface. Before you start installing your wood floor, make sure that the sub floor is already leveled. This is because if there is a void under your floorboards, it will make noise when people are stepping. The floor can be leveled using sands and topped with rubber made from recycled materials.
3. You can lay sub floor if needed. If you are going glue your floor, you have to make sure it has an even level. But if you are going to nail the floor, you need put a sub floor underneath. Make sure you put the right thickness of the sub floor and the plywood enough to nail the sub floor and plywood.
4. You can also consider a floating floor. It is one of the most inexpensive floors and easy to install, you don’t need to glue or nail it. A floating floor is also a good option when you have asbestos flooring before. The wood flooring can be installed at the top of the old floor you have. It saves you money from removing the asbestos from it.
5. Check the adhesive direction. When you are choosing for a glue for your floor, make sure you pick a particular brand of adhesive that dries quickly. To check this feature, you need to read the instruction. When gluing, work on small spread only. Don’t put too much on the floorboard even before it dried. You have to follow the instruction written in the adhesive direction.
6. Use engineered wood in damp areas. When there is a moisture issue in the area such as the kitchen, it might be best to use engineered wood floor which consists of layers of real wood attached together with thin layers of fiberboard or plywood. Depending on the thickness of the floor, the engineered wood can be refinished once or more.
7. Test the food when it comes to stain. When it comes to stain, the floor is unpredictable. There are wood floors that are very hard when it comes to removing stains. To test the wood floor, you can get a piece of wood and sample it. See if you are satisfied with the color with a stain on it.

Read More